Sunday, September 15, 2019

Simulated or Measured Performance for Simple Antennas?

Parent Category: 2018 HFE

By Yonghui Shu

Measuring antenna pattern and gain accurately is often a challenge. This is not only due to the demands of expensive test equipment, but also the requirement to have skilled and knowledgeable workers. In addition, it is impossible to avoid the interactions introduced by the test equipment and test fixtures/equipment holders.

Unlike most microwave component testing, antenna pattern and gain measurements need to be performed in an open-space environment with well controlled with minimum reflections. Currently, the widely used antenna pattern and gain measurement systems are realized in three categories: Far Field Range, Near Field Range, and Compact Range. In most cases, these systems are cumbersome and expensive, regardless of the frequency band. They become unaffordable once test equipment, such as a Vector Network Analyzer (VNA) or Synthesizer and Spectrum Analyzer are added, especially at millimeterwave bands. Because of that, most businesses cannot afford their own antenna range, and outsource the service instead.

The question is if antenna and gain measurement is even necessary today if the antennas are simple. In the meantime, measuring pattern is a very delicate and detailed task. It requires skilled and knowledgeable workers, often full-fledged microwave engineers, who are not only familiar with VAN, but also proficient with the setup and alignment of the Antenna Under Test (AUT) and Transmitter Antenna. Any misalignment or reflection caused by the test fixtures, etc., could introduce measurement errors and uncertainties.

1803 HFE better fg01

Modern EM Solvers are Mature

On the other hand, the modern EM solvers are mature. Today, most commercial available simulators, HFSS, CST, and uWave Wizard, can take account into all aspects to include the material and finishing properties, and give very accurate simulation results. In the meantime, mechanical design tools such as Solidworks and other tools are capable of taking the simulated structure to realize the physical antenna structures without losing the dimension accuracies. With help of the modern manufacturing tools, such as CNN machine centers, wire EDM, EDM Sinkers, and 3D printers, we can achieve the required accuracy in a straightforward manner.

1803 HFE better fg02

1803 HFE better fg03

Because of the above, the industry has accepted that simulated antenna patterns and gains for simple aperture antennas such as rectangular horns, circular horns, lens corrected antennas, scalar antennas, Gaussian antennas, Cassegrain Antennas, Reflector Antennas, and Omni Directional Antennas are very accurate. As long as the above processes are used, the produced antenna hardware will produce the patterns and gains that the simulator predicts. As a contrast, the measured antenna patterns and gains of these antennas are often distorted due to setup limitations and operator abilities. In other words, the measured patterns and gains are often less accurate than the simulated data. Based on above, SAGE Millimeter highly recommends using the simulated antenna gains and patterns instead of measured data for simple aperture antennas mentioned above.

To further ensure the call, we performed an investigation by measuring the patterns and gains of an E-band gain horn antenna. The results are shown on page 38.

The measured data and simulated data are very similar, but the simulated data is more accurate because the patterns are supposed to be symmetrical due to the antenna being symmetrical.

About the Author

Yonghui Shu is President of SAGE Millimeter.

September 2019

1909 HFE cover

The September 2019 Online Edition is now available for viewing and download!

Download September HFE PDF


Web Exclusives


AWR logo

e-Book – Microstrip Antenna Design

A new e-book, authored by industry veteran Kenneth Puglia and featuring NI AWR Design Environment software, explores microstrip antenna design and examines the single-element rectangular microstrip antenna as well as antenna arrays constructed from single microstrip elements. The eBook is available at (registration required).

Contact Us

Scott Spencer

Tim Burkhard
Associate Publisher
Fax: 707-544-9375

Gary Rhodes
VP Sales
Fax: 631-667-2871

Stuart Dale
Advertising Sales – New England

Jeff Victor
Advertising Sales - Western U.S. - New Accounts
Fax: 509-472-1888

Sam Baird
Advertising Sales - UK and Europe
+44 1883 715 697
Fax: +44 1883 715 697

Joanne Frangides
Advertising Sales - New Accounts & Product Showcase
Fax: 201-666-6698

Insulated Wire Inc.

Insulated Wire Inc. is pleased to announce that following the retirement of a French delegate, IW Microwave Products Division President, John Morelli, has been appointed as the Secretary for IEC/SC46F, a subcommittee of IEC/TC46. IEC/SC46F is responsible for RF and Microwave Connectors and Components International Standardization.

Mr. Morelli, who is sponsored by Insulated Wire, brings significant RF/Microwave connector and component experience to the position, and we congratulate him on his new appointment. Mr. Morelli had been serving as the chief Technical Advisor for the US National Committee’s Technical Advisory Group to IEC/SC46F.

The US National Committee of the IEC is a fully integrated entity of the American National Standards Institute (ANSI).

Coming Events

IMS 2019, Boston, June 2 - 7, 2019

IEEE EMC + SIPI, New Orleans, July 22 - 26, 2019

IEEE AUTOTESTCON, National Harbor, MD, September 9 – 12, 2019

EuMW 2019, Paris, September 29 - October 4, 2019

MILCOM 2019, location TBD, October 2019 (date TBD)

AOC, Washington, DC, October 28 - 30, 2019

IEEE Radio and Wireless Symposium, location TBD, January 2020 (date TBD)